Page 1 of 70 1231151 ... LastLast
Results 1 to 10 of 696

Thread: Ferrari 348 engine bay and rear end restoration.

  1. #1
    Join Date
    Feb 2011
    Location
    Gloucestershire
    Name
    Nick
    Posts
    995

    Default Ferrari 348 engine bay and rear end restoration.

    Hi guys,
    Firstly I would like to say what a great site. Full of interesting info and informed members. We all need to turn to it from time to time Im
    sure. Ive owned my car for getting on for three years and ive always had a plan in mind to do what Ive done in the last few months. I combined it
    with the need to renew the cam belt and carry out a service which as we all know requires the engine out to do this properly. As for myself ive been in the motor trade all my working life (35+years) and restoration is not an alien subject to me having done quite a few cars over the years. This is my first
    Ferrari resto though. This phase will just deal with the rear end of the car taking in the engine bay and associated framework, rear suspension, rear panel etc. I wont harp on about stuff thats already been covered on the site in much detail, ie cam belt replacement , timing , brake bleeding etc as I dont see the point in repeating spot on information. The whole process was carried out in a fully kitted workshop using both ramps and floorspace.
    Hope you enjoy the post.Name:  DSCF8169.jpg
Views: 3376
Size:  55.6 KBName:  DSCF8171.jpg
Views: 3188
Size:  81.8 KBName:  DSCF8237.jpg
Views: 3310
Size:  74.9 KBName:  DSCF8207.jpg
Views: 5388
Size:  94.0 KBName:  DSCF8235.jpg
Views: 3852
Size:  109.5 KBName:  DSCF8232.jpg
Views: 2647
Size:  99.2 KB
    Pic 1 Car on two poster ramp. I did most of the prelim stripping here. Fluids drained etc etc.
    Pic 2 View of engine being stripped. All looks a bit scruffy.
    Pic 3 Car positioned in floorspace with rear unit removed. Two jacks used plus the added security of stands. A must.
    Pic 4 Unit removed.
    Pic 5 Engine and gearbox removed from subframe.
    Pic 6 Subframe totally stripped apart from top suspension arms. The mounting bolts were seized to the middle of the bushes on both sides so had to be carefully cut of with a air hacksaw. Not hard but time consuming. General condition of frame was good. Solid with only some surface corrosion. Just looked mucky. More to come later.

  2. #2
    Nosevi's Avatar
    Nosevi is online now There's an outside too? Where? Super Moderator
    Join Date
    Jun 2011
    Location
    Lincolnshire
    Name
    Nos
    Posts
    10,610

    Default

    Very much looking forward to reading this - thanks for posting

  3. #3
    Join Date
    Feb 2011
    Location
    Gloucestershire
    Name
    Nick
    Posts
    995

    Default

    Just to say at this point in the project ( Ten days in) I fell over on some damp grass and broke my right wrist. Now it became somewhat difficult to
    work but I battled on. Its amazing how agile your left hand becomes with some practice.. At least I had managed to strip everything down before my accident so could get it all off to the powdercoaters and have an easier two weeks while waiting for the bits to come back. Got on with
    some lighter work in the mean time. There was a lot of it. Here are some pics of the restored subframe. I was looking for a factory sort of finish so I went for a textured look. This works for me. Name:  DSCF8285.jpg
Views: 2612
Size:  60.1 KBName:  DSCF8284.jpg
Views: 2596
Size:  90.0 KBName:  DSCF8283.jpg
Views: 2626
Size:  94.8 KBName:  DSCF8286.jpg
Views: 2511
Size:  73.3 KBName:  DSCF8287.jpg
Views: 2582
Size:  74.6 KB

  4. #4
    AJ3XX's Avatar
    AJ3XX is offline Looks like a 308 to me? -The Ferrari 288 GTO Club Member
    Join Date
    Sep 2010
    Location
    Chelmsford
    Name
    Andy
    Posts
    2,872

    Default

    Quote Originally Posted by Nosevi View Post
    Very much looking forward to reading this - thanks for posting
    + 1

    Great start
    Ferrari 348 - "still stands out from a crowd but yet still fits in” - Randy Stetson

  5. #5
    Join Date
    Feb 2011
    Location
    Gloucestershire
    Name
    Nick
    Posts
    995

    Default

    Name:  DSCF8278.jpg
Views: 2567
Size:  79.4 KBName:  DSCF8281.jpg
Views: 2547
Size:  69.1 KBName:  DSCF8274.jpg
Views: 2572
Size:  63.6 KB

    Some more restored engine parts and dry sump tank.

  6. #6
    Join Date
    Feb 2011
    Location
    Gloucestershire
    Name
    Nick
    Posts
    995

    Default

    Name:  DSCF8295.jpg
Views: 2451
Size:  41.3 KBName:  DSCF8296.jpg
Views: 2491
Size:  41.5 KB

    Main oil pipe between tank and engine had a cracked flange. Not a bad leak. Only a weep but still made a mess on floor over time. This repair was
    carried out by Pirtek Gloucester. He knew all about Ferrari pipes and the issues that go with them as he had repaired many over time. Mostly for a
    local specialist. He reused the tank fitting as they cant supply this sort of item. Perfect job and fitted spot on. Dont overtighten or they WILL crack
    the nut. Then you are looking for a very expensive pipe. Same goes for any other oil hoses on the car. If one is leaking from the connector and
    there is no obvious crack try loosening the nut and re-seating the pipe a tad. This has worked for me in years gone by. If not you need to strip out and inspect the components. You will obviously need to drain the oil for the last operation.

  7. #7
    Nosevi's Avatar
    Nosevi is online now There's an outside too? Where? Super Moderator
    Join Date
    Jun 2011
    Location
    Lincolnshire
    Name
    Nos
    Posts
    10,610

    Default

    Quote Originally Posted by Pangea View Post
    Name:  DSCF8278.jpg
Views: 2567
Size:  79.4 KBName:  DSCF8281.jpg
Views: 2547
Size:  69.1 KBName:  DSCF8274.jpg
Views: 2572
Size:  63.6 KB

    Some more restored engine parts and dry sump tank.
    When can I drop my car off? You do take orders I take it? Those look great

  8. #8
    Join Date
    Feb 2011
    Location
    Gloucestershire
    Name
    Nick
    Posts
    995

    Default

    Quote Originally Posted by Nosevi View Post
    When can I drop my car off? You do take orders I take it? Those look great
    They look a bit stark in those photos. Wrong setting on my crap camera. They look better in later pics.

  9. #9
    Nosevi's Avatar
    Nosevi is online now There's an outside too? Where? Super Moderator
    Join Date
    Jun 2011
    Location
    Lincolnshire
    Name
    Nos
    Posts
    10,610

    Default

    Quote Originally Posted by Pangea View Post
    They look a bit stark in those photos. Wrong setting on my crap camera. They look better in later pics.
    Look pretty good to me. Look forward to seeing the later shots

  10. #10
    Join Date
    Feb 2011
    Location
    Gloucestershire
    Name
    Nick
    Posts
    995

    Default

    Name:  DSCF8365.jpg
Views: 2380
Size:  97.7 KBName:  DSCF8371.jpg
Views: 2451
Size:  82.1 KBName:  DSCF8372.jpg
Views: 2478
Size:  57.9 KB

    I wanted to retain as many original parts as possible so here is a selection of items I had re-plated. Rubbers on the P clips and fuel filter brackets
    cleaned up lovely. Still nice and soft. Treated with rubber care solution. Autoglim. I wanted to put the throttle linkage in a glass case in my living
    room. Looks great.

Page 1 of 70 1231151 ... LastLast

Similar Threads

  1. 348 Engine Bay Clean - Phase 1 Complete!
    By Reado10 in forum Ferrari Talk
    Replies: 14
    Last Post: 20-05-2011, 04:32 PM
  2. 458 Engine Bay Fire - Not Again with Ferrari!!
    By Kenyon in forum Ferrari Talk
    Replies: 7
    Last Post: 17-07-2010, 06:09 PM
  3. 348 engine bay heatproof foam
    By photoman1963 in forum Ferrari Talk
    Replies: 0
    Last Post: 20-03-2010, 10:26 PM
  4. GT4 rear suspension/engine bay refurb
    By rmdferrari in forum Ferrari Talk
    Replies: 20
    Last Post: 28-01-2008, 01:18 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •